POST 的结果，机器，运行不正常。大家看看

大家看看那里出问题了，谢谢了

@(#)OBP 4.17.1 2005/04/11 14:24 Sun Blade 2500
Clearing TLBs
Power-On Reset
Executing Power On Self Test

@(#)OBP 4.17.1 2005/04/11 14:24 Sun Blade 2500
Clearing TLBs
POST Results: Cpu 0000.0000.0000.0000
  %o0 = 0000.0000.0000.0000 %o1 = ffff.ffff.f00d.08a6 %o2 = ffff.ffff.ffff.ffff
Membase: 0000.0000.0000.0000
MemSize: 0000.0000.0004.0000
Init CPU arrays Done
Init E$ tags Done
Setup TLB (small-footprint mode) Done
MMUs ON
Scrubbing Tomatillo tags... 0 1
Find dropin, Copying Done, Size 0000.0000.0000.81b0
PC = 0000.07ff.f000.70c8
PC = 0000.0000.0000.7178
Find dropin, Copying Done, Size 0000.0000.0001.1700
Diagnostic console initialized
Configuring system memory & CPU(s)

CPU 0 Speed: 1280 Mhz, ratio  8:1 , ECCR: f00c00
CPU 0 Memory Configuration: Valid
CPU 0 Bank 0 1024 MB Bank 1 <empty> Bank 2 <empty> Bank 3 <empty>
Master CPU 0 Membase: 0 Memsize: 40000000


@(#)OBP 4.17.1 2005/04/11 14:24 Sun Blade 2500
Clearing TLBs
Loading Configuration

Membase: 0000.0000.0000.0000
MemSize: 0000.0000.4000.0000
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Scrubbing Tomatillo tags... 0 1
Block Scrubbing Done
Find dropin, Copying Done, Size 0000.0000.0000.81b0
PC = 0000.07ff.f000.70c8
PC = 0000.0000.0000.7178
Find dropin, (copied), Decompressing Done, Size 0000.0000.0006.7c80
Diagnostic console initialized
System Reset: CPU Reset (SPOR)
Probing system devices
jbus at 0,0 SUNW,UltraSPARC-IIIi (1280 MHz @ 8:1, 1 MB) memory-controller
jbus at 1,0 Nothing there
jbus at 1c,0 pci ppm
jbus at 1d,0 pci
jbus at 1e,0 pci ppm
jbus at 1f,0 pci i2c
/i2c@1f,464000: nvram idprom
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device SUNW,fru-device SUNW,asr
Loading onboard drivers:
/pci@1e,600000: Device 7 isa
/pci@1e,600000/isa@7: flashprom rtc i2c power serial serial dma
/pci@1e,600000/isa@7/i2c@0,320: i2c-bridge gpio hardware-monitor hardware-monitor gpio gpio audio-card-fru-prom motherboard-fru-prom scsi-backplane-fru-prom dimm-spd dimm-spd clock-generator
/pci@1e,600000/isa@7/dma@0,0: parallel
Probing memory
CPU 0 Bank 0 base          0 size 1024 MB
Probing I/O buses
/pci@1f,700000: Device 2 ...(text may have been truncated due to an exception)

     ERROR: /pci@1f,700000/<Unnamed>: Last Trap: Data Access Error
/pci@1e,600000: Device 6 pmu
/pci@1e,600000/pmu@6: i2c beep ppm
/pci@1e,600000/pmu@6/i2c@0,0: card-reader
/pci@1e,600000: Device 8 sound
/pci@1e,600000: Device a usb
/pci@1e,600000: Device b usb
/pci@1e,600000: Device d ide disk cdrom
/pci@1e,600000: Device 2 Nothing there
/pci@1e,600000: Device 3 Nothing there
/pci@1e,600000: Device 4 pci
/pci@1e,600000/pci@4: Device 0 Nothing there
/pci@1e,600000/pci@4: Device 1 Nothing there
/pci@1e,600000/pci@4: Device 2 Nothing there
/pci@1e,600000/pci@4: Device 3 Nothing there
/pci@1e,600000/pci@4: Device 4 Nothing there
/pci@1e,600000/pci@4: Device 5 Nothing there
/pci@1e,600000/pci@4: Device 6 Nothing there
/pci@1e,600000/pci@4: Device 7 Nothing there
/pci@1e,600000/pci@4: Device 8 usb usb usb
/pci@1e,600000/pci@4: Device 9 Nothing there
/pci@1e,600000/pci@4: Device a Nothing there
/pci@1e,600000/pci@4: Device b firewire
/pci@1e,600000/pci@4: Device c Nothing there
/pci@1e,600000/pci@4: Device d Nothing there
/pci@1e,600000/pci@4: Device e Nothing there
/pci@1e,600000/pci@4: Device f Nothing there
/pci@1d,700000: Device 4 scsi disk tape scsi disk tape
/pci@1d,700000: Device 2 Nothing there
/pci@1c,600000: Device 3 network
/pci@1c,600000: Device 2 Nothing there
screen not found.
keyboard not found.
Keyboard not present.  Using ttya for input and output.

System Reset: CPU Reset (SPOR)
Probing system devices
jbus at 0,0 SUNW,UltraSPARC-IIIi (1280 MHz @ 8:1, 1 MB) memory-controller
jbus at 1,0 Nothing there
jbus at 1c,0 pci ppm
jbus at 1d,0 pci
jbus at 1e,0 pci ppm
jbus at 1f,0 pci i2c
/i2c@1f,464000: nvram idprom
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device SUNW,fru-device SUNW,asr
Loading onboard drivers:
/pci@1e,600000: Device 7 isa
/pci@1e,600000/isa@7: flashprom rtc i2c power serial serial dma
/pci@1e,600000/isa@7/i2c@0,320: i2c-bridge gpio hardware-monitor hardware-monitor gpio gpio audio-card-fru-prom motherboard-fru-prom scsi-backplane-fru-prom dimm-spd dimm-spd clock-generator
/pci@1e,600000/isa@7/dma@0,0: parallel
Probing memory
CPU 0 Bank 0 base          0 size 1024 MB
Probing I/O buses
/pci@1f,700000: Device 2 ...(text may have been truncated due to an exception)

     ERROR: /pci@1f,700000/<Unnamed>: Last Trap: Data Access Error
/pci@1e,600000: Device 6 pmu
/pci@1e,600000/pmu@6: i2c beep ppm
/pci@1e,600000/pmu@6/i2c@0,0: card-reader
/pci@1e,600000: Device 8 sound
/pci@1e,600000: Device a usb
/pci@1e,600000: Device b usb
/pci@1e,600000: Device d ide disk cdrom
/pci@1e,600000: Device 2 Nothing there
/pci@1e,600000: Device 3 Nothing there
/pci@1e,600000: Device 4 pci
/pci@1e,600000/pci@4: Device 0 Nothing there
/pci@1e,600000/pci@4: Device 1 Nothing there
/pci@1e,600000/pci@4: Device 2 Nothing there
/pci@1e,600000/pci@4: Device 3 Nothing there
/pci@1e,600000/pci@4: Device 4 Nothing there
/pci@1e,600000/pci@4: Device 5 Nothing there
/pci@1e,600000/pci@4: Device 6 Nothing there
/pci@1e,600000/pci@4: Device 7 Nothing there
/pci@1e,600000/pci@4: Device 8 usb usb usb
/pci@1e,600000/pci@4: Device 9 Nothing there
/pci@1e,600000/pci@4: Device a Nothing there
/pci@1e,600000/pci@4: Device b firewire
/pci@1e,600000/pci@4: Device c Nothing there
/pci@1e,600000/pci@4: Device d Nothing there
/pci@1e,600000/pci@4: Device e Nothing there
/pci@1e,600000/pci@4: Device f Nothing there
/pci@1d,700000: Device 4 scsi disk tape scsi disk tape
/pci@1d,700000: Device 2 Nothing there
/pci@1c,600000: Device 3 network
/pci@1c,600000: Device 2 Nothing there


Sun Blade 2500, No Keyboard
Copyright 2005 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.17.1, 1024 MB memory installed, Serial #56346988.
Ethernet address 0:3:ba:5b:c9:6c, Host ID: 835bc96c.




Running diagnostic script obdiag/normal

Testing /pci@1e,600000/pmu@6/i2c@0,0/card-reader@0,40
Testing /pci@1e,600000/ide@d
Testing /pci@1e,600000/pmu@6
Testing /pci@1e,600000/usb@b
Testing /pci@1e,600000/usb@a
Testing /pci@1e,600000/sound@8
Testing /pci@1c,600000/network@3
Testing /pci@1e,600000/isa@7/serial@0,2e8
Testing /pci@1e,600000/isa@7/serial@0,3f8
Testing /pci@1e,600000/isa@7/i2c@0,320:tests={[email protected]}
Testing /pci@1e,600000/isa@7/i2c@0,320:tests={[email protected]}
Testing /pci@1e,600000/isa@7/i2c@0,320:tests={[email protected]}
Testing /pci@1e,600000/isa@7/i2c@0,320:tests={[email protected]}
Testing /pci@1e,600000/isa@7/i2c@0,320:tests={[email protected]}
Testing /pci@1e,600000/isa@7/i2c@0,320:tests={[email protected]}
Testing /pci@1e,600000/isa@7/i2c@0,320:tests={[email protected]}

   WARNING : Device hardware-monitor@0,52 not found in device tree
   DEVICE  : /pci@1e,600000/isa@7/i2c@0,320:tests={[email protected]}

Testing /pci@1e,600000/isa@7/i2c@0,320:tests={[email protected]}
Testing /pci@1e,600000/isa@7/i2c@0,320:tests={[email protected]}
Testing /pci@1e,600000/isa@7/rtc@0,70
Testing /pci@1e,600000/isa@7/flashprom@2,0
Testing /pci@1e,600000/isa@7/dma@0,0/parallel@0,378
Testing /pci@1d,700000/scsi@4
Testing /pci@1d,700000/scsi@4,1


Initializing     1MB of memory at addr          3fecc000 -
                                                                     
Initializing     1MB of memory at addr          3fec0000 -
                                                                     
Initializing     1MB of memory at addr          3fe90000 -
                                                                     
Initializing     1MB of memory at addr          3fd50000 -
                                                                     
Initializing    14MB of memory at addr          3f000000 -
                                                                     
Initializing  1008MB of memory at addr                 0 -
                                                                     
Aborting auto-boot sequence.
ok boot disk

@(#)OBP 4.17.1 2005/04/11 14:24 Sun Blade 2500
Clearing TLBs
Loading Configuration

Membase: 0000.0000.0000.0000
MemSize: 0000.0000.4000.0000
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Scrubbing Tomatillo tags... 0 1
Block Scrubbing Done
Find dropin, Copying Done, Size 0000.0000.0000.81b0
PC = 0000.07ff.f000.70c8
PC = 0000.0000.0000.7178
Find dropin, (copied), Decompressing Done, Size 0000.0000.0006.7c80
Diagnostic console initialized
System Reset: CPU Reset
Probing system devices
jbus at 0,0 SUNW,UltraSPARC-IIIi (1280 MHz @ 8:1, 1 MB) memory-controller
jbus at 1,0 Nothing there
jbus at 1c,0 pci ppm
jbus at 1d,0 pci
jbus at 1e,0 pci ppm
jbus at 1f,0 pci i2c
/i2c@1f,464000: nvram idprom
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device SUNW,fru-device SUNW,asr
Loading onboard drivers:
/pci@1e,600000: Device 7 isa
/pci@1e,600000/isa@7: flashprom rtc i2c power serial serial dma
/pci@1e,600000/isa@7/i2c@0,320: i2c-bridge gpio hardware-monitor hardware-monitor gpio gpio audio-card-fru-prom motherboard-fru-prom scsi-backplane-fru-prom dimm-spd dimm-spd clock-generator
/pci@1e,600000/isa@7/dma@0,0: parallel
Probing memory
CPU 0 Bank 0 base          0 size 1024 MB
Probing I/O buses
/pci@1f,700000: Device 2 ...(text may have been truncated due to an exception)

     ERROR: /pci@1f,700000/<Unnamed>: Last Trap: Data Access Error
/pci@1e,600000: Device 6 pmu
/pci@1e,600000/pmu@6: i2c beep ppm
/pci@1e,600000/pmu@6/i2c@0,0: card-reader
/pci@1e,600000: Device 8 sound
/pci@1e,600000: Device a usb
/pci@1e,600000: Device b usb
/pci@1e,600000: Device d ide disk cdrom
/pci@1e,600000: Device 2 Nothing there
/pci@1e,600000: Device 3 Nothing there
/pci@1e,600000: Device 4 pci
/pci@1e,600000/pci@4: Device 0 Nothing there
/pci@1e,600000/pci@4: Device 1 Nothing there
/pci@1e,600000/pci@4: Device 2 Nothing there
/pci@1e,600000/pci@4: Device 3 Nothing there
/pci@1e,600000/pci@4: Device 4 Nothing there
/pci@1e,600000/pci@4: Device 5 Nothing there
/pci@1e,600000/pci@4: Device 6 Nothing there
/pci@1e,600000/pci@4: Device 7 Nothing there
/pci@1e,600000/pci@4: Device 8 usb usb usb
/pci@1e,600000/pci@4: Device 9 Nothing there
/pci@1e,600000/pci@4: Device a Nothing there
/pci@1e,600000/pci@4: Device b firewire
/pci@1e,600000/pci@4: Device c Nothing there
/pci@1e,600000/pci@4: Device d Nothing there
/pci@1e,600000/pci@4: Device e Nothing there
/pci@1e,600000/pci@4: Device f Nothing there
/pci@1d,700000: Device 4 scsi disk tape scsi disk tape
/pci@1d,700000: Device 2 Nothing there
/pci@1c,600000: Device 3 network
/pci@1c,600000: Device 2 Nothing there
screen not found.
keyboard not found.
Keyboard not present.  Using ttya for input and output.

System Reset: CPU Reset
Probing system devices
jbus at 0,0 SUNW,UltraSPARC-IIIi (1280 MHz @ 8:1, 1 MB) memory-controller
jbus at 1,0 Nothing there
jbus at 1c,0 pci ppm
jbus at 1d,0 pci
jbus at 1e,0 pci ppm
jbus at 1f,0 pci i2c
/i2c@1f,464000: nvram idprom
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device SUNW,fru-device SUNW,asr
Loading onboard drivers:
/pci@1e,600000: Device 7 isa
/pci@1e,600000/isa@7: flashprom rtc i2c power serial serial dma
/pci@1e,600000/isa@7/i2c@0,320: i2c-bridge gpio hardware-monitor hardware-monitor gpio gpio audio-card-fru-prom motherboard-fru-prom scsi-backplane-fru-prom dimm-spd dimm-spd clock-generator
/pci@1e,600000/isa@7/dma@0,0: parallel
Probing memory
CPU 0 Bank 0 base          0 size 1024 MB
Probing I/O buses
/pci@1f,700000: Device 2 ...(text may have been truncated due to an exception)

     ERROR: /pci@1f,700000/<Unnamed>: Last Trap: Data Access Error
/pci@1e,600000: Device 6 pmu
/pci@1e,600000/pmu@6: i2c beep ppm
/pci@1e,600000/pmu@6/i2c@0,0: card-reader
/pci@1e,600000: Device 8 sound
/pci@1e,600000: Device a usb
/pci@1e,600000: Device b usb
/pci@1e,600000: Device d ide disk cdrom
/pci@1e,600000: Device 2 Nothing there
/pci@1e,600000: Device 3 Nothing there
/pci@1e,600000: Device 4 pci
/pci@1e,600000/pci@4: Device 0 Nothing there
/pci@1e,600000/pci@4: Device 1 Nothing there
/pci@1e,600000/pci@4: Device 2 Nothing there
/pci@1e,600000/pci@4: Device 3 Nothing there
/pci@1e,600000/pci@4: Device 4 Nothing there
/pci@1e,600000/pci@4: Device 5 Nothing there
/pci@1e,600000/pci@4: Device 6 Nothing there
/pci@1e,600000/pci@4: Device 7 Nothing there
/pci@1e,600000/pci@4: Device 8 usb usb usb
/pci@1e,600000/pci@4: Device 9 Nothing there
/pci@1e,600000/pci@4: Device a Nothing there
/pci@1e,600000/pci@4: Device b firewire
/pci@1e,600000/pci@4: Device c Nothing there
/pci@1e,600000/pci@4: Device d Nothing there
/pci@1e,600000/pci@4: Device e Nothing there
/pci@1e,600000/pci@4: Device f Nothing there
/pci@1d,700000: Device 4 scsi disk tape scsi disk tape
/pci@1d,700000: Device 2 Nothing there
/pci@1c,600000: Device 3 network
/pci@1c,600000: Device 2 Nothing there


Sun Blade 2500, No Keyboard
Copyright 2005 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.17.1, 1024 MB memory installed, Serial #56346988.
Ethernet address 0:3:ba:5b:c9:6c, Host ID: 835bc96c.



Initializing     1MB of memory at addr          3fec0000 -
                                                                     
Initializing    15MB of memory at addr          3f000000 -
                                                                     
Initializing  1008MB of memory at addr                 0 -
                                                                     
Rebooting with command: boot disk
Boot device: /pci@1d,700000/scsi@4/disk@0,0  File and args:
Evaluating:

Can't open boot device

ok probe-scsi-all
/pci@1d,700000/scsi@4,1

/pci@1d,700000/scsi@4

ok set probe-ide
  Device 0  ( Primary Master )
         Not Present

  Device 1  ( Primary Slave )
         Not Present

  Device 2  ( Secondary Master )
         Removable ATAPI Model: JLMS XJ-HD166S                          

  Device 3  ( Secondary Slave )
         Not Present

ok
ok
ok
ok
ok set-defaults
Setting NVRAM parameters to default values.
ok reset-all

     ERROR: /pci@1f,700000/<Unnamed>: Last Trap: Data Access Error
screen not found.
keyboard not found.
Keyboard not present.  Using ttya for input and output.

     ERROR: /pci@1f,700000/<Unnamed>: Last Trap: Data Access Error


Sun Blade 2500, No Keyboard
Copyright 2005 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.17.1, 1024 MB memory installed, Serial #56346988.
Ethernet address 0:3:ba:5b:c9:6c, Host ID: 835bc96c.



Initializing     1MB of memory at addr          3fee0000 -
                                                                     
Initializing     1MB of memory at addr          3fec0000 -
                                                                     
Initializing    15MB of memory at addr          3f000000 -
                                                                     
Initializing  1008MB of memory at addr                 0 -
                                                                     
Aborting auto-boot sequence.
ok boot disk power-off
ok

自己顶下

本帖最后由 东方蜘蛛 于 2010-08-26 13:36 编辑

DEVICE  : /pci@1e,600000/isa@7---这个是主板的TTYA/TTYB
ERROR: /pci@1f,700000------这个路径是PCI Slot 5  /pci@1f,700000/<device>@2,*  33/66MHz 32/64bit 3.3V/L
也许会给你些提示，让你想起些什么

IO bus:

/pci@1f,700000: Device 2 ...(text may have been truncated due to an exception)

     ERROR: /pci@1f,700000/<Unnamed>: Last Trap: Data Access Error

And i2c bus controller got error:

Testing /pci@1e,600000/isa@7/i2c@0,320:tests={[email protected]}

   WARNING : Device hardware-monitor@0,52 not found in device tree
   DEVICE  : /pci@1e,600000/isa@7/i2c@0,320:tests={[email protected]}


Both components locate on motherboard, so the motherboard should be replaced.

LZ可以考虑先把PCI5上的卡拔掉再做个POST看看，不行就换主板吧