gentoo无法识别matrox 的scsi硬盘？

Linux version 2.6.24-gentoo-r5 (root@miranda) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #1 SMP Thu Jun 26 18:36:15 UTC 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000dfff0000 (usable)
 BIOS-e820: 00000000dfff0000 - 00000000dfffe000 (ACPI data)
 BIOS-e820: 00000000dfffe000 - 00000000e0000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec86000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
Warning only 4GB will be used.
Use a HIGHMEM64G enabled kernel.
3200MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 1048576) 0 entries of 256 used
Zone PFN ranges:
 DMA 0 -> 4096
 Normal 4096 -> 229376
 HighMem 229376 -> 1048576
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
 0: 0 -> 1048576
On node 0 totalpages: 1048576
 DMA zone: 32 pages used for memmap
 DMA zone: 0 pages reserved
 DMA zone: 4064 pages, LIFO batch:0
 Normal zone: 1760 pages used for memmap
 Normal zone: 223520 pages, LIFO batch:31
 HighMem zone: 6400 pages used for memmap
 HighMem zone: 812800 pages, LIFO batch:31
 Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F7A50, 0014 (r0 ACPIAM)
ACPI: RSDT DFFF0000, 0030 (r1 A M I OEMRSDT 3000517 MSFT 97)
ACPI: FACP DFFF0200, 0084 (r2 A M I OEMFACP 3000517 MSFT 97)
ACPI: DSDT DFFF0420, 4513 (r1 DPX8H DPX8HV11 0 INTL 2002026)
ACPI: FACS DFFFE000, 0040
ACPI: APIC DFFF0390, 0090 (r1 A M I OEMAPIC 3000517 MSFT 97)
ACPI: OEMB DFFFE040, 0040 (r1 A M I AMI_OEM 3000517 MSFT 97)
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x06] enabled)
Processor #6 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] enabled)
Processor #1 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] enabled)
Processor #7 15:4 APIC version 20
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x0b] address[0xfec10000] gsi_base[72])
IOAPIC[1]: apic_id 11, version 32, address 0xfec10000, GSI 72-95
ACPI: IOAPIC (id[0x09] address[0xfec81000] gsi_base[24])
IOAPIC[2]: apic_id 9, version 32, address 0xfec81000, GSI 24-47
ACPI: IOAPIC (id[0x0a] address[0xfec81400] gsi_base[48])
IOAPIC[3]: apic_id 10, version 32, address 0xfec81400, GSI 48-71
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 4 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at e2000000 (gap: e0000000:1ec00000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1040384
Kernel command line: root=/dev/ram0 init=/linuxrc dokeymap looptype=squashfs loop=/image.squashfs cdroot initrd=gentoo.igz BOOT_IMAGE=gentoo doscsi dosshd nox
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
mapped IOAPIC to ffff9000 (fec10000)
mapped IOAPIC to ffff8000 (fec81000)
mapped IOAPIC to ffff7000 (fec81400)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0725000 soft=c06e5000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2992.701 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 3609424k/4194304k available (3857k kernel code, 59408k reserved, 1819k data, 316k init, 2752448k highmem)
virtual kernel memory layout:
 fixmap : 0xffc74000 - 0xfffff000 (3628 kB)
 pkmap : 0xff800000 - 0xffc00000 (4096 kB)
 vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
 lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
 .init : 0xc0692000 - 0xc06e1000 ( 316 kB)
 .data : 0xc04c4762 - 0xc068b6dc (1819 kB)
 .text : 0xc0100000 - 0xc04c4762 (3857 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5989.03 BogoMIPS (lpj=29945161)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000641d 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
CPU 1 irqstacks, hard=c0726000 soft=c06e6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5985.16 BogoMIPS (lpj=29925807)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000641d 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
SMP alternatives: switching to SMP code
Booting processor 2/6 eip 3000
CPU 2 irqstacks, hard=c0727000 soft=c06e7000
Initializing CPU#2
Calibrating delay using timer specific routine.. 5985.23 BogoMIPS (lpj=29926183)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 3
CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000641d 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#2.
CPU2: Intel P4/Xeon Extended MCE MSRs (24) available
CPU2: Thermal monitoring enabled
CPU2: Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
SMP alternatives: switching to SMP code
Booting processor 3/7 eip 3000
CPU 3 irqstacks, hard=c0728000 soft=c06e8000
Initializing CPU#3
Calibrating delay using timer specific routine.. 5985.23 BogoMIPS (lpj=29926172)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000641d 00000000 00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 3
CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000641d 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#3.
CPU3: Intel P4/Xeon Extended MCE MSRs (24) available
CPU3: Thermal monitoring enabled
CPU3: Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
Total of 4 processors activated (23944.66 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
checking TSC synchronization [CPU#0 -> CPU#2]: passed.
checking TSC synchronization [CPU#0 -> CPU#3]: passed.
Brought up 4 CPUs
net_namespace: 64 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=7
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0500-053f claimed by ICH4 GPIO
PCI: PXH quirk detected, disabling MSI for SHPC device
PCI: PXH quirk detected, disabling MSI for SHPC device
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EPA0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EPA1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EPA1.PXHA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EPA1.PXHB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PB._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PA._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 6B, should be 5C [20070126]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 17 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 3.00 loaded.
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Device 0000:02:01.0 not found by BIOS
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
system 00:09: ioport range 0x4d0-0x4d1 has been reserved
system 00:09: ioport range 0x400-0x47f has been reserved
system 00:09: ioport range 0x500-0x53f has been reserved
system 00:09: iomem range 0xfec10000-0xfec1ffff could not be reserved
system 00:09: iomem range 0xfed20000-0xfed8ffff has been reserved
system 00:0b: iomem range 0xffc00000-0xfff7ffff could not be reserved
system 00:0c: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0c: iomem range 0xfee00000-0xfee00fff could not be reserved
system 00:0e: ioport range 0x680-0x6ff has been reserved
system 00:0e: ioport range 0x295-0x296 has been reserved
system 00:0f: iomem range 0xe0000000-0xefffffff has been reserved
system 00:10: iomem range 0x0-0x9ffff could not be reserved
system 00:10: iomem range 0xc0000-0xdffff could not be reserved
system 00:10: iomem range 0xe0000-0xfffff could not be reserved
system 00:10: iomem range 0x100000-0xdfffffff could not be reserved
system 00:10: iomem range 0xfff80000-0xffffffff could not be reserved
PCI: Bridge: 0000:00:02.0
 IO window: disabled.
 MEM window: disabled.
 PREFETCH window: disabled.
PCI: Bridge: 0000:04:00.0
 IO window: disabled.
 MEM window: disabled.
 PREFETCH window: disabled.
PCI: Bridge: 0000:04:00.2
 IO window: 9000-dfff
 MEM window: fe600000-feafffff
 PREFETCH window: fc100000-fc1fffff
PCI: Bridge: 0000:00:03.0
 IO window: 9000-dfff
 MEM window: fe600000-feafffff
 PREFETCH window: fc100000-fc1fffff
PCI: Bridge: 0000:00:1c.0
 IO window: 8000-8fff
 MEM window: fe400000-fe5fffff
 PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
 IO window: 5000-7fff
 MEM window: fc300000-fe3fffff
 PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.0 to 64
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:03.0 to 64
PCI: Setting latency timer of device 0000:04:00.0 to 64
PCI: Setting latency timer of device 0000:04:00.2 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
checking if image is initramfs...<7>Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 2
Switched to high resolution mode on CPU 3
Switched to high resolution mode on CPU 0
 it is
Freeing initrd memory: 18613k freed
Machine check exception polling timer started.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1233336475.690:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.3 (2007/10/31) Phillip Lougher
JFS: nTxBlock = 8192, nTxLock = 65536
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
OCFS2 1.3.3
OCFS2 Node Manager 1.3.3
OCFS2 DLM 1.3.3
OCFS2 DLMFS 1.3.3
OCFS2 User DLM kernel interface loaded
GFS2 (built Jun 26 2008 18:35:08) installed
Lock_Nolock (built Jun 26 2008 18:35:18) installed
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Boot video device is 0000:01:04.0
PCI: Setting latency timer of device 0000:00:02.0 to 64
Allocate Port Service[0000:00:02.0:pcie00]
PCI: Setting latency timer of device 0000:00:03.0 to 64
Allocate Port Service[0000:00:03.0:pcie00]
intel_rng: FWH not detected
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: module loaded
input: Macintosh mouse button emulation as /class/input/input0
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: MAP [ IDE IDE P0 P1 ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
ata1.00: ATAPI: GCR-8483B, 1.03, max UDMA/33
ata1.00: configured for UDMA/33
scsi 0:0:0:0: CD-ROM HL-DT-ST CD-ROM GCR-8483B 1.03 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k
EDAC MC: Ver: 2.1.0 Jun 26 2008
EDAC e752x: tolm = e0000, remapbase = 100000, remaplimit = 11c000
EDAC MC0: Giving out device to 'e752x_edac' 'E7320': DEV 0000:00:00.0
EDAC PCI0: Giving out device to module 'e752x_edac' controller 'EDAC PCI controller': DEV '0000:00:00.0' (POLLED)
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Using IPI No-Shortcut mode
rtc_cmos 00:02: setting system clock to 2009-01-30 17:27:58 UTC (1233336478)
Freeing unused kernel memory: 316k freed
ata1: soft resetting link
ata1.00: configured for UDMA/33
ata1: EH complete
CAPI Subsystem Rev 1.1.2.8
b1: revision 1.1.2.2
sr 0:0:0:0: Attached scsi generic sg0 type 5
NCR53c406a: no available ports found
scsi: <fdomain> Detection failed (no card)
qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>seagate: ST0x/TMC-8xx not detected.
Failed initialization of WD-7000 SCSI card!
NCR53c406a: no available ports found
sym53c416.c: Version 1.0.0-ac
Fusion MPT base driver 3.04.06
Copyright (c) 1999-2007 LSI Corporation
Fusion MPT SPI Host driver 3.04.06
ACPI: PCI Interrupt 0000:05:05.0[A] -> GSI 52 (level, low) -> IRQ 18
mptbase: ioc0: Initiating bringup
ioc0: LSI53C1030 B2: Capabilities={Initiator}
scsi4 : ioc0: LSI53C1030 B2, FwRev=01032700h, Ports=1, MaxQ=222, IRQ=18
ACPI: PCI Interrupt 0000:05:05.1[b] -> GSI 53 (level, low) -> IRQ 19
mptbase: ioc1: Initiating bringup
 target4:0:0: mptspi: ioc0: mpt_config failed
ioc1: LSI53C1030 B2: Capabilities={Initiator}
scsi5 : ioc1: LSI53C1030 B2, FwRev=01032700h, Ports=1, MaxQ=222, IRQ=19
Fusion MPT FC Host driver 3.04.06
Fusion MPT SAS Host driver 3.04.06
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.010.
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.14)
Adaptec aacraid driver 1.1-5[2449]-ms
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.10-rc5 Thu May 17 10:09:32 PDT 2007
QLogic Fibre Channel HBA Driver
Emulex LightPulse Fibre Channel SCSI driver 8.2.2
Copyright(c) 2004-2007 Emulex. All rights reserved.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfebffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e880
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 19 (level, low) -> IRQ 21
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000ec00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
sl811: driver sl811-hcd, 19 May 2005
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: [email protected]
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
async_tx: api initialized (async)
xor: automatically using best checksumming function: pIII_sse
 pIII_sse : 4600.800 MB/sec
xor: using function: pIII_sse (4600.800 MB/sec)
raid6: int32x1 788 MB/s
raid6: int32x2 827 MB/s
raid6: int32x4 614 MB/s
raid6: int32x8 554 MB/s
raid6: mmxx1 1809 MB/s
raid6: mmxx2 1874 MB/s
raid6: sse1x1 1108 MB/s
raid6: sse1x2 1190 MB/s
raid6: sse2x1 2193 MB/s
raid6: sse2x2 1948 MB/s
raid6: using algorithm sse2x1 (2193 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 75 (level, low) -> IRQ 22
e1000: 0000:02:03.0: e1000_probe: (PCI:66MHz:32-bit) 00:14:2a:23:bb:00
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 74 (level, low) -> IRQ 23
e1000: 0000:02:04.0: e1000_probe: (PCI:66MHz:32-bit) 00:14:2a:23:bb:01
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
rtc: I/O resource 70 is not free.
warning: process `hwsetup' used the deprecated sysctl system call with 1.23.
input: PC Speaker as /class/input/input2
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
ACPI: PCI Interrupt 0000:00:1f.3[b] -> GSI 17 (level, low) -> IRQ 24
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: Processor [CPU1] (supports 8 throttling states)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP]
I2O subsystem v1.325
i2o: max drivers = 8
i2o: Checking for PCI I2O controllers...
ACPI: Unable to derive IRQ for device 0000:02:01.0
ACPI: PCI Interrupt 0000:02:01.0[?]: no GSI
iop0: controller found (0000:02:01.0)
iop0: PCI I2O controller at 00000000 size=0
iop0: Unable to map controller.
iop0: DMA / IO allocation for I2O controller failed
ACPI: Unable to derive IRQ for device 0000:02:01.0
PCI_I2O: probe of 0000:02:01.0 failed with error -12
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
ACPI: Unable to derive IRQ for device 0000:02:01.0
ACPI: PCI Interrupt 0000:02:01.0[?]: no GSI
dpti: adpt_config_hba: io remap failed
Could not Init an I2O RAID device
Will not try to detect others.
warning: process `hwsetup' used the deprecated sysctl system call with 1.49.
warning: process `hwsetup' used the deprecated sysctl system call with 1.49.
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
dpti: adpt_config_hba: io remap failed
Could not Init an I2O RAID device
Will not try to detect others.
No dock devices found.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth1: link is not ready
ADDRCONF(NETDEV_UP): eth0: link is not ready
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Bridge firewalling registered
eth0: no IPv6 routers present